Back to shop
  •
1 3

MCM Power Brick Holder - VHB Plate (2-pack)

MCM Power Brick Holder - VHB Plate (2-pack)

$4.99 USD
$4.99 USD
Sale
Shipping calculated at checkout.

Sold Out (this item will not be restocked)
Description

WARNING: VHB should be considered a "permanent" adhesive - removing VHB tape after it has been applied may cause damage to paint or other surfaces.

Magnetic Cable Management VHB Plates are an optional upgrade for standard Magnetic Cable Management plates. 3M VHB is a legend in the industry for a reason - their adhesive is second to none. We always recommend screwing your plates into your desk or wall for maximum hold, but if you insist on only using an adhesive solution... VHB is the way to go.

Includes:
- 2 Power Brick Holder VHB Steel Plates

HOW TO INSTALL

  • Clean your mounting surface with 70% isopropyl alcohol or soap and water solution to remove any dirt or oil that may interfere with the adhesive backing. 
  • Peel the backing layer off a loose plate (or magnetically connected plate and arch) to expose the adhesive. 
  • Press the plate (or connected plate and arch) against the surface in the desired location. 
  • Apply firm pressure to the plate or arch against the mounting surface for at least 10 seconds. 
  • For maximum security, screw your plate into your mounting surface with the included screws. 
  • For more detailed installation instructions, please refer to 3M's installation documentation here.

If you used a Magnetic Arch to help position your adhesive plate: 

  1. Carefully remove the arch from the plate (Tip: reaching inside the arch to hold the plate against the surface while sliding the arch sideways can be helpful) 

  2. Ensure good contact between the entire plate to the mounting surface by firmly pressing all areas of the plate against the mounting surface.

Disclaimer: This only comes with the VHB plates for the Power Brick Holders. Power Brick Holders are sold separately. See "Related Products" below.

Product Information
- Includes 2 x Power Brick Holder VHB Magnetic Plates
Related Products
MCM Power Brick Holder (2-pack)

MCM Power Brick Holder (2-pack)

MCM Power Brick Holder (2-pack)

$14.99 USD
$14.99 USD
View full details

Customer Reviews

Based on 275 reviews
84%
(232)
13%
(37)
2%
(5)
0%
(1)
0%
(0)
M
M.A. (Stanfield, US)
Good stuff

Slap that baby on and add the metal plates and you are set, strong magnet, simple use and installation.

C
Cameron C. (Barrington, US)
Amazing

Have had them for a little over a month and have been amazing and made my set up look amazing

J
Jack T. (Adelaide, AU)
Perfect for Milwaukee chargers

I purchased the 2 pack of powerbar magnets with the intention of putting them on the backside of my milwaukee battery charger at work. They work fantastically. The pair of magnets are strong enough to support the weight of the heaviest 18v battery and a 12v battery at the same time whilst being mounted on the side, fighting gravity and resisting sliding.

S
Samuel K. (Chicago, US)

All the cable management gear is excellently made and does exactly what it needs to. These power keys are just a little confusing to figure out how to install them when you first get them. It took me awhile to realize you're supposed to keep the triangular plastic piece attached.

Wish that LTT would do a tutorial video that clearly shows how to install/use all the products in the intended manner.

N
Nathan P.

I know they said they worked really hard to increase the strength of the magnets as much as possible, but even so I was not expecting even the small arches to be this strong. I have an Anker extension cord / gan charger combo which unfortunately doesn't have a power bar key, but one small arch is enough to comfortably hold it on the side of my desk even with the extra weight of the connected cords and dc adapters.

123